﻿SDS200A + SoftScope2 고객 통합 패키지 / Complete Customer Package — 2026-10-27
사용설명서 개정 / Guide revision: 2

[한국어]
이 통합 ZIP에는 SoftScope2 2.5.0 제조사 원본 설치 파일, SDS200A 드라이버 지원 ZIP, 한국어·영어 PDF/DOCX 설명서가 들어 있습니다.
대상: Windows 10/11 64비트(x64). ARM64와 32비트 Windows는 대상이 아닙니다.

1. 이 통합 ZIP 전체를 일반 폴더에 압축 해제하세요.
2. SoftScope2 2.5.0이 아직 설치되지 않았다면 Software/setup.exe로 본체 프로그램을 먼저 설치하세요. 이미 2.5.0이 설치돼 있다면 본체를 다시 설치할 필요는 없습니다.
3. Driver/SDS200A-Legacy-x64-20261027.zip도 별도 폴더에 전체 압축 해제하세요.
4. SDS200A를 USB로 연결하고, Driver 안의 ZIP을 푼 폴더에서 Check.cmd를 실행하세요.
5. 같은 폴더의 Install.cmd를 실행하세요. 인증서 지문과 적용 범위를 확인한 뒤 INSTALL을 입력하고 관리자 권한(UAC)을 승인하세요.
6. Check.cmd에서 장치 상태를 확인하고 SoftScope2에서 실제 장치 연결과 파형 취득을 확인하세요. 정상 재부팅 후에도 다시 점검하세요.

설명서 개정 2에서 말하는 'ZIP/패키지'는 Driver/SDS200A-Legacy-x64-20261027.zip을 뜻하며, 'release.json'은 Driver/release.json입니다. 설명서의 SoftScope2 사전 설치 단계는 이 통합 ZIP의 Software/setup.exe로 진행할 수 있습니다.
Software/setup.exe는 디지털 서명이 없는 제조사 원본 설치 파일이며 수정하지 않았습니다. 원본 출처와 SHA256은 Software/source-info.json에 있습니다.
드라이버 설치 시 공개 인증서를 PC의 신뢰 저장소에 등록합니다. Microsoft WHQL 인증 패키지는 아닙니다. 설치 절차에 테스트 모드나 드라이버 서명 검사 해제는 포함되지 않습니다.
Windows 11 동작 확인은 사용자 보고이며 해당 빌드 번호는 확인되지 않았습니다. 모든 Windows 11 빌드와 보안 설정에서의 호환성을 보증하지 않습니다.
상세 설치·문제 해결·제거는 Manuals의 한국어 PDF/DOCX 설명서를 참고하세요. 드라이버 제거는 드라이버 ZIP을 푼 폴더의 Remove.cmd를 사용하세요.

[English]
This complete ZIP contains the original SoftScope2 2.5.0 manufacturer installer, the SDS200A driver support ZIP, and Korean/English PDF and DOCX guides.
Target: Windows 10/11 x64. ARM64 and 32-bit Windows are not supported by this package.

1. Extract this entire complete ZIP to a normal folder.
2. If SoftScope2 2.5.0 is not installed, install the application first using Software/setup.exe. If version 2.5.0 is already installed, you do not need to reinstall it.
3. Also fully extract Driver/SDS200A-Legacy-x64-20261027.zip to a separate folder.
4. Connect the SDS200A by USB and run Check.cmd from the folder extracted from that driver ZIP.
5. Run Install.cmd in the same folder. Review the certificate fingerprint and scope, type INSTALL, and approve the administrator (UAC) prompt.
6. Check the device state with Check.cmd, then confirm real device connection and waveform acquisition in SoftScope2. Check again after a normal restart.

In guide revision 2, references to the 'ZIP/package' mean Driver/SDS200A-Legacy-x64-20261027.zip; references to 'release.json' mean Driver/release.json. Its SoftScope2 prerequisite can be installed using Software/setup.exe from this complete ZIP.
Software/setup.exe is the unchanged, unsigned legacy manufacturer installer. Its source and SHA256 are recorded in Software/source-info.json.
Driver installation enrolls the public certificate in the PC's trust stores. This package is not Microsoft WHQL certified. The installation procedure does not enable test mode or disable driver signature enforcement.
Successful Windows 11 operation was reported by a user; the build is unknown. Compatibility with every Windows 11 build and security configuration is not guaranteed.
See the English PDF/DOCX guides in Manuals for installation, troubleshooting and removal. Use Remove.cmd from the extracted driver ZIP to remove the device package.
